Most of the Candy washing machines have a program for identifying faults and errors, displaying them in the form of codes on the display. Data Candy Washing Machine Error Codes will be deciphered in this article. This system is available only for machines with a display, because others that do not have it display errors in a different way.
With these encrypted codes, which provide the information necessary to troubleshoot a problem, the technician can quickly identify the problem and begin the repair process. However, in order to understand what the error is, you need to know the designation of these error codes. Below will be the error codes of the Candy washing machine. Since errors are displayed in different ways in different models, we will divide them into subspecies.
ActivaSmart Model Errors
E01 - occurs when the door lock device of the Kandy washing machine fails. If this error occurs, the door lock may malfunction, and the wiring and integrity of the electronic controller may also be broken.
E02 - occurs when there is a problem of water intake, i.e. water does not enter the cavity of the household unit or, on the contrary, exceeds its optimal amount. With this error, clogging or clogging of the filler valve, or even its failure, is possible. It is also possible that the level sensor and controller malfunction.
E03 - issued by the unit when the water is drained slowly or does not occur at all. This error is manifested when the contacts and conductors of the drain pump are broken or broken. The washing machine water level sensor is damaged or out of order. It is also possible that the drain pipes and filters could be clogged.
E04 - consists in a malfunction of the filling valves, overfilling above the programmed set water level in the tank. The signal comes from the level control relay that the tank is full and the machine stops. This problem is explained by the failure of the water level control controller, which is stuck in one position and the filling valve lets water through.
E05 - the water does not heat up at all or very weakly. When an E05 error occurs, there may be several reasons. First, the tubular electric heater has become unusable. Secondly, the thermal sensor is faulty. Third, the water level controller refuses to work.
E07 - engine operation at increased speeds, exceeding the permissible ones by the program. This error is caused by a breakdown of the tacho sensors and the generator. With this breakdown, in any case, you need to check the motor winding and replace it if it is faulty.
E09 - the electric drive does not work or does not work as it should. When this error appears, the motor power supply unit is replaced or the drive rewound.
See also - Washing machine water supply solenoid valve - check and replace
Aquatic model errors
These models of Candy washing machines do not have a display as such. All codes with errors are given in the form of blinking indicators located on the control panels of these machines. Blinking is based on the Morse code, you need to closely monitor the behavior of the indicator and count blinks. These errors are shown below:
- The indicator is on without blinking, without stopping - a malfunction of the control module or its violation.
- Blinking once - a malfunction of the washing machine door interlock device, and the wiring and integrity of the electronic controller may also be violated.
- Flashes twice - no water arriving or arriving, but too slow. It is necessary to check if the water supply valve is closed, and also to check the integrity of the water supply hose. The water level sensor or its contacts are faulty.
- Blinks three times - there is water in the machine after draining. Drain pump malfunction, clogged filter or drain hose.
- Flashes four times - the tank is full. It occurs due to clogged filling valves, the level sensor is faulty or contacts.
- Blinking five times - the thermal sensor is closed or the integrity of the wiring is broken.
- Flashes six times - control module and memory are faulty.
- Blinking seven times - the drive is stopped.
- Eight flashes - the tachometer or generator has closed.
- Nine flashes - the triac of the electric drive is faulty.
- Twelve flashes - there is no signal between the control module and the indicator module. Contacts broken.
- Fourteen blinks - a malfunction of the control module, as well as a violation of contacts.
- Fifteen blinks - program failure.
- Sixteen - shorting of the tubular electric heater.
- Seventeen is an incorrect signal from the tachometer.
- Eighteen is an electrical problem.
All these Kandy washing machine error codes and repair instructions can also be found on the manufacturer's website and in the technical documentation supplied in the kit. If you are not confident in your abilities, we recommend that you turn to specialists for help, they will diagnose and accurately establish the cause of the failure of the Kandy washing machine.
See also:
- 13 best washing machines from 40,000 to 50,000 rubles according to customer reviews
- 15 of the best washing machines
- 15 best washing machines from 30,000 to 40,000 rubles according to customer reviews
- 5 best Whirlpool washing machines according to customer reviews
- 6 best Bosch washing machines according to customer reviews
