Not sure what happened to your washing machine, which caused it to jump, vibrate violently and make uncharacteristic sounds? Perhaps she slipped off her legs or became wrong. But strong vibration can also indicate a more serious problem that needs to be addressed immediately. So that could be causing the noise. We will try to figure it out before this problem gets worse.
Why does the washing machine start jumping when spinning
There are many reasons why the washing machine jumps and makes more noise. Let's take a look at what problems can cause strong vibration of the washing machine:
- During washing, small objects can get caught between the drum and the tub, for example, sometimes we can wash things with coins, paper clips, bed linen with pins, or small buttons and fasteners get caught.
- If the transit bolts were not removed during installation.
- The laundry is not correctly distributed in the drum of the machine (found in older models of washing machines).
- If your electric motor is broken.
- The washer is not properly installed on the supports.
- Check if the bearings are out of order.
- Springs and shock absorbers are defective or badly worn out.
- Another reason may be loosening of the mount or deformation of the counterweight.
See also - The washing machine constantly draws in water and drains it immediately - what to do?
Troubleshooting
The problems are manifold, and it is very difficult to immediately find out what could have caused the strong vibrations. Therefore, it would be more rational to exclude, first the simplest options, the washing machine rattles and shakes. What to do to find out simple reasons why the washing machine jumps when spinning:
- Look carefully to see if the linen is wrapped in a knot, it often happens that small items of clothing are hammered into a duvet cover or sweaters.
- Check if the amount of laundry in the machine exceeds the maximum allowable. Different permissible values are possible for each wash mode and machine model.
- Noise can occur when items take up more than 2/3 of the drum volume.
In such cases, some washing machines are equipped with a special sensor that displays errors such as UE or UB on the display.
How to install the washing machine so that it does not jump?
Strong vibrations can often be caused by incorrect installation or typical errors, especially when the equipment is installed by non-professionals or the installation is done independently. The most common mistake is shipping boltswho simply forget to remove or install the apparatus unevenly or put it on a slippery surface (tile), which causes wobbling and, as a result, loud noise.
Why does the washing machine jump when installed incorrectly and what to do:
- The first step is to remove the shipping brackets. They are installed to fix the drum so that it is not damaged during transportation.If they are not removed, the drum will spin, but its wear will be greatly increased, and the operation of the apparatus itself will be accompanied by strong vibration and bouncing.
- Carefully ensure that the equipment is set strictly according to the level. To do this, you can twist the legs and adjust their height. When spinning, the machine enters into resonance and may even move around the room, so it is not recommended to leave faulty equipment in working condition unattended.
- After completing the installation, check if the device is wobbling. Any, even the slightest, swaying can lead to jumping. If the washing machine is wobbling, then it will have to be leveled.
Even if the equipment will be installed by professionals, it is better to check these nuances yourself to make sure everything is in order. Be sure to test the work after installation. Such actions will help you save time on the subsequent repeated call of the installers so that they fix the malfunction and not wonder what to do so that the machine does not emit frightening sounds.
Defective shock absorbers
It is necessary to inspect the shock absorbers, which serve to cushion shock when the drum is moving, reduce loads and dampen vibrations. If the device vibrates or jumps heavily, the shock absorbers may need to be replaced. Shock absorbers are mounted together with spring mechanisms, but if only the shock absorbers are worn out, they can be replaced separately, if the springs are out of order, then everything will have to be changed at once. Over time, shock absorbers wear out, and they cannot be repaired - replaced immediately. Wear may be uneven, but if only one is defective, both shock absorbers must be replaced to ensure balanced load distribution.
Look for small items under the drum. If they are, then you have to get them. For example, a bra bone or a paper clip can be easily reached; if you pick it up with something, you can make something like a hook, which will be convenient for pulling out small parts. If smaller parts are stuck that cannot be reached, you will have to disassemble the washing machine. To do this, you need to remove the heating element, drum and some other parts. If you have never disassembled washing machines, then it is better to call a master who will do it as quickly as possible, which will save you a lot of time, but most importantly, it is safe for equipment.
See also - A bra bone in the washing machine
Counterweight Mounting Problems
If the washing machine starts to vibrate and jump violently, you need to check the operation of the counterweight. We open the cover at the top of the device, for this you may need tools, it will be enough to use keys, a screwdriver and pliers. We look at the state of the counterweight, it is a weighting agent made of different materials. Such parts are installed at the top and bottom of the washing machine. They can be made of concrete, cast iron, or other heavy material.
What to do next:
- We look at the fasteners, if they are loose, then you will need to tighten them.
- If you cannot tighten the fasteners, you will have to purchase and install new ones.
- If the weighting agent itself is deformed, you cannot do without replacing it with the same one.
One of the reasons the machine can jump is bearing failure. The replacement process is technically difficult, so it is better to call a master who can do this work with high quality. If you still want to do this yourself, you will need more information about this process, so you can read the corresponding article about it.
Bearing problem
Faults associated with bearing breakage are far from uncommon. The main reasons for the breakdown of this part are associated with the fact that the metal from which the elements are made deteriorates over time due to exposure to water.When the bearings begin to deteriorate, the operation of the apparatus will first be accompanied by increased vibration and noise, and then the drum may completely wedge.
When a bearing is just beginning to fail, it is difficult to identify problems. Usually, professionals can tell about wear and tear of a part by sound, but this requires experience and knowledge. But when the bearing is already badly damaged, you can move the drum. When he moves in different directions, it says it's time to call the master to replace worn out bearing.
What can we talk about in the end? It turns out that the washing machine is a complex system that needs professional help to fix technical problems and it is worth contacting qualified specialists with experience and knowledge to quickly and effectively fix the problem.
See also:
