Do-it-yourself troubleshooting of a washing machine tank

Content:

How to disassemble the washing machine tank yourself?
Dismantling and installing bearings
What to do if the washing machine tank is leaking
Is it possible to repair deformed tank walls
Other possible malfunctions and their repair
Assembling a refurbished tank

The breakdown of an automatic washing machine for a modern housewife is akin to a typhoon, which brings many troubles. But, fortunately, a faithful knight in the face of her husband, if he has golden hands, can put the spoiled miracle of technology in order, even if such a complex operation as replacing or repairing a washing machine tank is ahead.

How to disassemble the washing machine tank yourself?

Washing machine tank repair

It is quite possible to disassemble the tank with your own hands at home, even if the instructions say that it is a non-separable type.
When repairing a washing machine tank, the main thing at the first stage is to determine where the seam is located on its body, connecting both sides during soldering. The design can be with two bearings or with one, but the conditions of the problem do not change from this, you just have to knock out one more. Step-by-step instructions for disassembling the washing machine:

Along the entire perimeter of the seam, places are marked where it will be necessary to drill holes in the future - this operation is necessary for fasteners at the end of the work. Their distance should be approximately 5 to 9 cm, but no more so that there are no leaks. The diameter of the holes in the washing machine tank should not exceed 3 - 5 mm. As a result, you get about 20 marks. Now you need an electric drill and a drill - three millimeters, in order to drill the marked holes.
Then you need to cut the tank clearly along the seam. This stage of repairing a washing machine is one of the longest and most crucial moments, which will require accuracy and patience. The whole difficulty is not to damage other parts of the machine tank with a hacksaw.
After the welding seam is dismantled, the washing machine tank will be divided into two parts - front and back. They are most often made of plastic material. These parts differ from each other. The front is a kind of ring, but a slightly distorted shape, and in the middle it has a hatch and a rubber cuff. The rear half consists of a drum, as well as a drive mechanism, a bearing, a wheel for a variable transmission pulley.
Now finding the cause of the breakdown and making the necessary repairs is not so difficult. The rear half should be turned over so that it is the drum hatch downwards. It is more convenient to put it on bars or other convenient device for further work. In general, it is not difficult to disassemble the shaft, but you need to be able not to damage the screw, which is located in the middle - this is the main fastener. In order for the screw to be free to unscrew, a rod is required, preferably metal. Professional craftsmen advise using a center punch for these needs. It is enough to direct the rod to the screw, and then hit it with a hammer. Usually a few times is enough. Now using a Phillips screwdriver, the screw can be removed without problems.
The shaft must be removed from the stem in accordance with all the rules of plumbing.Before performing this operation and carrying out repairs, you need to stock up on wooden blocks of different sizes. Large ones - useful as a stand under the edges of the tank, giving it stability. A small block is required in order to direct it to the stem and hit with a hammer several times. First you need to hit lightly, then a little harder, then even harder, this will lead to the fact that the drum will separate from the body.

Dismantling and installing bearings

replacement of bearings for a washing machine tank

Before removing the bearings, which are located in the casing of the washing machine tank, you must make sure that they are broken. If, after inspection, it turns out that they are in working order, they do not need to be removed. In the event that deformation is found after inspection of the bearings, a problem in the oil seals, as well as other malfunctions, they must be replaced.
You will also need a metal bar to remove the washing machine bearings. It needs to be positioned on the edge of the part, and applied a few gentle blows with a hammer. Moving the rod to the other side - the blows are repeated. You should beat in diameter, but not on one side, otherwise the bearing will jam, and there will be a problem how to pull it out. If it is skewed, then you can drill it with a stepped drill. Then, in place of the old ones, new ones are installed. This completes the repair of failed bearings.

What to do if the washing machine tank is leaking

If the tank itself is damaged, or rather, its walls are deformed, the first step is to assess the degree of damage. Usually the plastic part suffers the most. It often cracks, and the water entering it begins to seep. When repairing such tanks, it is better not to seal the cracks (since this is short-lived), but to completely change the entire part. Moreover, the plastic version is not so expensive.
Another thing is with tanks made of stainless steel. If this begins to leak, then the problem area can be welded - in this case, the machine will serve for a long time. In this case, it is better to entrust the repair to a professional welder. After the weld seam, it is necessary to cover with a special waterproof enamel. This will help increase the life of the element, and the washing machine as a whole.
There are no other methods of fixing damaged tanks yet. Only a complete replacement of a worn out tank or a full-fledged welding can save you.

Is it possible to repair deformed tank walls

If the tank is bent, it can also be repaired by hand, but only if the defect is small and the tank is free of holes. Required repair tools: a hammer and a small piece of wood.
The place where the dent is located must be heated from the outside. The block must be placed in the place that corresponds to the internal defect, and while the surface is warm, gently tap with a hammer until the dent is straightened.

repair deformed tank walls

Other possible malfunctions and their repair

Now you need to check the operation of the drain valve and the drain hole of the tank, since blockages often form in them and small but annoying breakdowns occur.
The drain hole must be cleaned of debris and dirt. For this, it is better to use sandpaper. It often turns out that the sealing rubber has become unusable or the cuff of the drain valve is worn out. This is noticeable right away: the rubber has lost its elasticity, has become unbending, and cracked.

Assembling a refurbished tank

After all the defective parts have been repaired, the tank is assembled in the reverse order from how it was disassembled. Having reached the procedure for joining the edges of the sawn element, you should coat it with a sealant or use cold welding.When the edges are connected, then through the holes made earlier, it is required to install the bolts and secure them with nuts. The diameter of the bolts must match the diameter of the drill.
If the malfunction of the washing machine is not very serious, you can disassemble the tank and make repairs yourself at home. But if the breakdown is very significant, it is better to hand the washing machine into the hands of a professional technician by contacting a service center.

See also: